How to Recover MS SQL Database from Suspect Mode?

Summary: Read this post to find solutions to recover MS SQL database marked as suspect. It describes step-wise instructions to fix the ‘SQL server suspect database’ issue by running Transact-SQL (T-SQL) commands in SQL Server Management Studio (SSMS). Also, it provides an alternative solution to restore the database using a SQL Recovery tool.

When SQL database goes into suspect mode, it becomes inaccessible. In such a situation, you will neither be able to connect to the database nor recover it during server startup.

Check out the Infographic below for quick solutions to recover database from suspect mode in SQL Server 2008, and higher versions.

When does SQL database goes to suspect mode?

When SQL server suspects the primary filegroup of the database to be damaged or if the database file is missing, the database status is set to ?Suspect?.

Also, there are a wide range of errors that could result in SQL database in suspect mode. Some of them are listed as below:

• System fails to open the device where the data or log file of SQL server resides.
• SQL server crashes or restarts in the middle of a transaction, resulting in a corrupt or inaccessible transactions log file.
• SQL Server tries to open a database, and the file belonging to that database is already open by anti-virus software installed on your system.
• The database is terminated abnormally.
• Lack of disk space.
• SQL cannot complete a rollback or roll forward operation.
• Database files are being held by the operating system, third-party backup software, etc.

How to get SQL database out of suspect mode?

NOTE: You can try restoring the database in suspect mode from a good known backup. If the backup is not available, proceed with the following steps.

Follow the steps in sequence given below to recover MS SQL database from suspect mode:

Step 1: Open SSMS and connect to the database.

Step 2: Select the New Query option.

Step 3: In the Query editor window, enter the following code to turn off the suspect flag on the database and set it to EMERGENCY:

EXEC sp_resetstatus ?db_name?;
ALTER DATABASE db_name SET EMERGENCY

NOTE: If you cannot set the database in emergency mode, skip to the next solution.

Step 4: A suspect database might not be corrupted. You can determine if the database is corrupted or not by running the following DBCC CHECKDB command.

DBCC CHECKDB (?database_name?)

This statement will report any consistency errors (if found) in the database and will recommend running the minimum level of repair option to fix corruption.

Before initiating the repair process, you must first set the database into ‘Single User Mode.’ Doing so will prevent other users from making any changes to the database during the repair process.

Step 5: Now, let?s bring the database into the Single User mode and roll back the previous transactions by executing the below command:

ALTER DATABASE database_name SET SINGLE_USER WITH ROLLBACK IMMEDIATE

Step 6: Take a complete backup of the corrupted files to avoid chances of data loss.

Step 7: After putting the db in SINGLE USER mode, try to fix the consistency errors using the REPAIR_REBUILD option of DBCC CHECKDB. This option can quickly repair missing rows in nonclustered indexes. In addition, you can use it for more time-consuming repair operation, such as rebuilding an index.

DBCC CHECKDB (?database_name?, REPAIR_REBUILD)

However, if REPAIR_ALLOW_DATA_LOSS is suggested as minimum level of repair, then run DBCC CHECKDB with the suggested repair option. The syntax is as follows: 

DBCC CHECKDB (?database_name?, REPAIR_ALLOW_DATA_LOSS)

Step 8: Bring the database into the Multi-User mode:

ALTER DATABASE database_name SET MULTI_USER

ALTER DATABASE database_name SET MULTI_USER

Step 9: Refresh the database server.

After completing these steps, you should be able to connect to the database. In case of any data loss, you?ll have the db backup to restore from (Step 6).

What if this solution doesn?t work?

If your server database file has turned severely corrupt, the above-mentioned steps may fail to revive the database. At this point, try restoring the database by using Stellar Repair for MS SQL.

The software can fix common SQL database corruption errors that occur due to reasons such as the database in suspect mode and several others. The software uses advanced algorithms to repair and restore SQL db from suspect mode to normal state (online).

How to Recover SQL Database from Suspect Mode with the Stellar SQL Recovery Tool?

Additional features of the software

• Repairs corrupt MDF and NDF files.
• Recovers tables, triggers, keys, indexes, stored procedures, defaults, rules, schema, etc.
• Supports MS SQL 2019, 2017, 2016, 2014, 2012, 2008 R2, and lower versions.
• Provides multiple saving options to save the repaired database including MS SQL (MDF), CSV, HTML, and XLS.

The software is trusted by Microsoft MVPs

Conclusion

This post discussed methods on ?How to recover MS SQL database from suspect mode?. The best approach is to restore the database from a healthy backup. If you don?t have backup, use the EMERGENCY mode to access the database and repair it. However, you may fail to rollback the transactions that were active when database went into suspect mode. Also, using the REPAIR_ALLOW_DATA_LOSS option as the minimum repair level can lead to data loss. A better alternative is to use a specialized SQL database repair software that helps repair and restore the database from suspect to a normal state.

Related Post